Best Cisco 200-301 2025 Training With 970 QA's
Cisco 200-301 Certification Exam Questions
The CCNA exam has recently undergone significant changes with the introduction of the new Cisco 200-301 exam. 200-301 exam replaces all previous CCNA exams and is designed to validate the skills needed for today's job roles in networking. The new exam covers a wide range of topics including network fundamentals, network access, IP connectivity, IP services, security fundamentals, automation and programmability.
Implementing and Administering Cisco Solutions (CCNA) v1.0
This training is intended to provide a broad understanding of fundamental IT concepts around networking and security. It uses hands-on lab, self-study, and lectures to ensure a candidate is familiar with a series of concepts around the installation, operation, configuration, and verification of network components. These include routers, LAN controllers, and switches. Also, this training helps learners build a strong foundation around software-centered networking, automation, and programmability.
NEW QUESTION # 357
Which two actions influence the EIGRP route selection process? (Choose two)
- A. The router calculates the best backup path to the destination route and assigns it as the feasible successor.
- B. The router must use the advertised distance as the metric for any given route
- C. The advertised distance is calculated by a downstream neighbor to inform the local router of the bandwidth on the link
- D. The router calculates the feasible distance of all paths to the destination route
- E. The router calculates the reported distance by multiplying the delay on the exiting Interface by 256.
Answer: A,D
Explanation:
Explanation
The reported distance (or advertised distance) is the cost from the neighbor to the destination. It is calculated from the router advertising the route to the network. For example in the topology below, suppose router A & B are exchanging their routing tables for the first time. Router B says "Hey, the best metric (cost) from me to IOWA is 50 and the metric from you to IOWA is 90" and advertises it to router A.
Router A considers the first metric (50) as the Advertised distance. The second metric (90), which is from NEVADA to IOWA (through IDAHO), is called the Feasible distance.
The reported distance is calculated in the same way of calculating the metric. By default (K1 = 1, K2 = 0, K3
= 1, K4 = 0, K5 = 0), the metric is calculated as follows:
NEW QUESTION # 358
Refer to Exhibit.
How does SW2 interact with other switches in this VTP domain?
- A. It receives updates from all VTP servers and forwards all locally configured VLANs out all trunk ports
- B. It transmits and processes VTP updates from any VTP Clients on the network on its trunk ports
- C. It forwards only the VTP advertisements that it receives on its trunk ports.
- D. It processes VTP updates from any VTP clients on the network on its access ports.
Answer: C
NEW QUESTION # 359
Drag and drop the functions from the left onto the correct network components on the right
Answer:
Explanation:
NEW QUESTION # 360
Drag and drop the IPv6 address type characteristics from the left to the right.
Answer:
Explanation:
NEW QUESTION # 361
Which interface mode must be configured to connect the lightweight APs in a centralized architecture?
- A. WLAN dynamic
- B. management
- C. access
- D. trunk
Answer: C
Explanation:
While the Cisco WLCs always connect to 802.1Q trunks, Cisco lightweight APs do not understand VLAN tagging and should only be connected to the access ports of the neighbor switch.
This is an example switch port configuration from the Catalyst 3750: interface GigabitEthernet1/0/22 description Access Port Connection to Cisco Lightweight AP switchport access vlan 5 switchport mode access no shutdown Reference:
https://www.cisco.com/c/en/us/support/docs/wireless/4400-series-wireless-lan-controllers/69719- wlc-lwap-config.html
NEW QUESTION # 362
Drag and Drop Question
Drag and drop the IPv6 addresses from the left onto the corresponding address types on the right.
Answer:
Explanation:
NEW QUESTION # 363
Connectivity between four routers has been established. IP connectivity must be configured in the order presented to complete the implementation. No dynamic routing protocols are included.
1. Configure static routing using host routes to establish connectivity from router R3 to the router R1 Loopback address using the source IP of 209.165.200.230.
2. Configure an IPv4 default route on router R2 destined for router R4.
3. Configure an IPv6 default router on router R2 destined for router R4.
Answer:
Explanation:
See the Explanation below.
Explanation:
Answer as below configuration:
1.- on R3
config terminal
ip route 192.168.1.1 255.255.255.255 209.165.200.229
end
copy running start
2.- on R2
config terminal
ip route 0.0.0.0 0.0.0.0 209.165.202.130
end
copy running start
3.- on R2
config terminal
ipv6 route ::/0 2001:db8:abcd::2
end
copy running start
NEW QUESTION # 364
Lab Simulation 6
Refer to the exhibit.
Three switches must be configured for Layer 2 connectivity. The company requires only the designated VLANs to be configured on their respective switches and permitted accross any links between switches for security purposes. Do not modify or delete VTP configurations.
The network needs two user-defined VLANs configured:
VLAN 110: MARKETING
VLAN 210: FINANCE
1. Configure the VLANs on the designated switches and assign them as access ports to the interfaces connected to the PCs.
2. Configure the e0/2 interfaces on Sw1 and Sw2 as 802.1q trunks with only the required VLANs permitted.
3. Configure the e0/3 interfaces on Sw2 and Sw3 as 802.1q trunks with only the required VLANs permitted.
Answer:
Explanation:
Sw1
enbale
config t
Vlan 210
Name FINANCE
Inter e0/1
Switchport access vlan 210
do wr
Sw2
Enable
config t
Vlan 110
Name MARKITING
Int e0/1
Switchport acees vlan 110
do wr
Sw3
Enable
config t
Vlan 110
Name MARKITING
Vlan 210
Name FINANCE
Int e0/0
Switchport access vlan 110
Int e0/1
Switchport access vlan 210
Sw1
Int e0/1
Switchport allowed vlan 210
Sw2
Int e0/2
Switchport trunk allowed vlan 210
Sw3
Int e0/3
Switchport trunk allowed vlan 210
Switchport trunk allowed vlan 210,110
NEW QUESTION # 365
Refer to the Exhibit. After the switch configuration the ping test fails between PC A and PC B Based on the output for switch 1. Which error must be corrected?
- A. Access mode is configured on the switch ports.
- B. All VLANs are not enabled on the trunk
- C. There is a native VLAN mismatch
- D. The PCs are m the incorrect VLAN
Answer: C
Explanation:
From the output we see the native VLAN of Switch1 on Gi0/1 interface is VLAN 1 while that of Switch2 is VLAN 99 so there would be a native VLAN mismatch.
NEW QUESTION # 366
Two switches are connected and using Cisco Dynamic Trunking Protocol. SW1 is set to Dynamic Auto and SW2 is set to Dynamic Desirable.
What is the result of this configuration?
- A. The link becomes a trunk port.
- B. The link becomes an access port.
- C. The link is in a down state.
- D. The link is in an error disabled state.
Answer: A
NEW QUESTION # 367
Router R1 must send all traffic without a matching routing-table entry to 192.168.1.1. Which configuration accomplishes this task?
- A. R1#Config t
R1(config)#ip routing
R1(config)#ip default-gateway 192.168.1.1 - B. R1#Config t
R1(config)#ip routing
R1(config)#ip route 0.0.0.0 0.0.0.0 192.168.1.1 - C. R1#Config t
R1(config)#ip routing
R1(config)#ip route default-route 192.168.1.1 - D. R1#Config t
R1(config)#ip routing
R1(config)#ip route 192.168.1.1 0.0.0.0 0.0.0.0
Answer: B
Explanation:
Section: IP Connectivity
NEW QUESTION # 368
Refer to the exhibit. An administrator must configure interfaces GM/1 and GM/3 on switch SW11. PC-1 and PC-2 must be placed in the Data VLAN, and Phone-1 must be placed in the Voice VLAN. Which configuration meets these requirements?
- A. Option D
- B. Option B
- C. Option A
- D. Option C
Answer: A
NEW QUESTION # 369
Drag and drop the statements about networking from the left onto the corresponding networking types on the right
Answer:
Explanation:
NEW QUESTION # 370
Refer to the exhibit.
What are two conclusions about this configuration? {Choose two.)
- A. The spanning-tree mode is Rapid PVST+.
- B. The designated port is FastEthernet 2/1.
- C. The root port is FastEthernet 2/1.
- D. This is a root bridge.
- E. The spanning-tree mode is PVST+.
Answer: A
NEW QUESTION # 371
What is a function of TFTP in network operations?
- A. transfers IOS images from a server to a router for firmware upgrades
- B. transfers files between file systems on a router
- C. transfers a configuration files from a server to a router on a congested link
- D. transfers a backup configuration file from a server to a switch using a username and password
Answer: A
Explanation:
TFTP is mostly used (Firmware upgrade) whereby the admin have the IOS image on one device and uses TFTP to load the image to all other devices quickly.
NEW QUESTION # 372
Drag and drop the characteristic from the left onto the IPv6 address type on the right.
Answer:
Explanation:
Explanation
Graphical user interface, application Description automatically generated
NEW QUESTION # 373
Which two functions are performed by the core layer in a three-tier architecture? (Choose two)
- A. Ensure timely data transfer between layers.
- B. Police traffic that is sent to the edge of the network.
- C. Provide uninterrupted forwarding service.
- D. Inspect packets for malicious activity.
- E. Provide direct connectivity for end user devices.
Answer: A,C
Explanation:
Cisco is very clear about the purpose of this layer. Its only role is to forward traffic, the fastest it can. Here you don't apply any policy, as you must try to reduce the load of the core so it can focus on routing.
https://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/Campus/campover.html#wp708831
NEW QUESTION # 374
Which two command sequences must be configured on a switch to establish a Layer 3 EtherChannel with an open-standard protocol? (Choose two.) interface GigabitEthernet0/0/1
- A. channel-group 10 mode auto
interface GigabitEthernet0/0/1 - B. channel-group 10 mode on
interface port-channel 10 - C. no switchport
ip address 172.16.0.1 255.255.255.0
interface GigabitEthernet0/0/1 - D. channel-group 10 mode active
interface port-channel 10 - E. switchport
switchport mode trunk
Answer: C,D
NEW QUESTION # 375
Drag drop the descriptions from the left onto the correct configuration-management technologies on the right.
Answer:
Explanation:
NEW QUESTION # 376
......
Quickly and Easily Pass Cisco Exam with 200-301 real Dumps: https://topexamcollection.pdfvce.com/Cisco/200-301-exam-pdf-dumps.html